![24 Hour Fan-Aspirated Radiation Shield for weather station](http://www.davisinstruments.com/cdn/shop/products/6838-radiation-shield_384x266.jpg?v=1618524204)
24-Hour Fan-Aspirated Radiation Shield - SKU 6838
A motor-driven fan draws a constant airflow through the sensor chamber at 500 feet per minute (2,5 m/s). At night, when the effects of radiation a...
View full detailsA motor-driven fan draws a constant airflow through the sensor chamber at 500 feet per minute (2,5 m/s). At night, when the effects of radiation a...
View full detailsAdd these high gain external antenna to your Gateway and/or Nodes to increase the transmission distance of an EnviroMonitor mesh network up to 6,00...
View full detailsSee the data from your Cabled Vantage Pro2 integrated sensor suite on your computer with WeatherLink or online with WeatherLinkIP Install the Cabl...
View full detailsReplacement reed switch cover for rain collector tipping bucket in all wireless and cabled Vantage Pro2, original Vantage Pro, Weather Wizard II, a...
View full detailsVantage Pro2 Plus Upgrade Kit. Save over $100 when compared to buying each component separately. Upgrade a vantage Pro2 to a Vantage Pro2 Plus with...
View full detailsEasily replace the tipping bucket assembly in your rain collector with the more accurate tipping spoon. Reports in inches. Comes with a 40′ (12 m) ...
View full detailsIncludes waterproof coupler kits (not shown in photograph) for joining two cables together, indoors and out. Not suitable to extend any Temperatur...
View full detailsIncludes waterproof coupler kits (not shown in photograph) for joining two cables together, indoors or out. Not suitable to extend any Temperature...
View full detailsReplacement kickstand for Vantage Pro2 and original Vantage Pro consoles. Does not include Hinge Arm or back cover. For full assemply, see the Re...
View full detailsThis replacement wind vane for Vantage Pro2 stations includes a brass tip and is compatible with anemometers that have D-shaped vane shafts. To avo...
View full detailsReplacement magnet end cap for tipping bucket for rain collector cones in all wireless and cabled Vantage Pro2 and original Vantage Pro stations ma...
View full detailsReplacement reed switch for rain collector tipping spoon in all wireless and cabled Vantage Pro2 sensor suites. 19” (0,5 m) sensor cable.
8' (2.5M) extension cable for serial port versions of WeatherLink for Vantage stations.
For mounting a solar radiation sensor, a UV sensor, or a radiation shield. Bracket is pre-driller for easy mounting. Includes mounting hardware.
Use with Long-Range Repeater to extend range up to 1,580′ (475 m) in all directions. Each repeater requires two antennas. You can combine omni and...
View full detailsPCBA for Vantage Vue Wireless Sensor Suite Weather Station, US
Install your Weather Envoy or Envoy8X outside with solar power and shelter. Use with a Universal Shelter to power a Vantage Vue or Vantage Pro2 co...
View full detailsOur USB-to-Serial cable will connect a device with a serial connector to your USB port on your computer. For use with WeatherLink Software with se...
View full detailsUse to adapt standard (inches) rain collector tipping bucket to metric measurements (mm) in all wireless and cabled Vantage Pro2 and Vantage Pro st...
View full detailsA temperature probe placed in the direct sun, or where it is exposed to a radiant heat source such as a building or concrete will not provide accu...
View full detailsReplacement battery door for all Vantage Pro2 and Vantage Pro consoles.
Replacement base for rain collector cones in all wireless and cabled Vantage Pro2 stations. Does not include tipping bucket assembly.
The Vantage Pro2 GroWeather wireless weather station is an agriculture-focused weather station that includes all the features of Vantage Pro2, plus...
View full detailsCharges an EnviroMonitor Node where sunlight is too low to use solar. Includes 5.5 ft. (1,6 m) cable.